Barrels and Accessories

  1. BARREL CAP 4"+S30 VALVE, KING KEG
    BARREL CAP 4"+S30 VALVE, KING KEG
    £13.00
    Out of stock

    4" Black Barrel top complete with Hambleton Bard S30 valve and 'o' ring seal. Fits Brewmaster and King Keg Barrels.

    Cap may come with the brass or Stainless S30 valve depending on availability. Both valves can be used with the S30 gas bottle or the 8gm individual gas bulbs (black holder needed to operate).

    Learn More
  2. King Keg Barrel - Top Tap (5 Gallon / 23 Litre)
    King Keg Barrel - Top Tap (5 Gallon / 23 Litre)
    £51.95
    Holds 5 Gallons (23 litres) and comes with a large lid (which allows you to get your hand in to clean) complete with a Hambleton Bard S30 valve. The valve is designed to allow extra gas (pressure) to be inserted into the barrel and also allows release of excess pressure that might build up during secondary fermentation. Learn More
  3. King Keg Barrel - Bottom Tap (5 Gallon / 23 Litre)
    King Keg Barrel - Bottom Tap (5 Gallon / 23 Litre)
    £49.96
    Holds 5 Gallons (23 litres) and comes with a large lid (which allows you to get your hand in to clean) complete with a Hambleton Bard S30 valve. Learn More
  4. DRUM TAP + NUT, LONG PARALLEL THREAD
    DRUM TAP + NUT, LONG PARALLEL THREAD
    £4.49
    This tap cannot be used on barrels with 2" caps. The spout of this tap takes 3/8" (9mm) bore tubing. To fit to buckets and wide neck fermenters the hole size required is 1 inch (25.4mm). Learn More
  5. QUICKSERVE TAP (LEVER ACTION)
    QUICKSERVE TAP (LEVER ACTION)
    £3.40
    This tap has a tapered thread and should only be used with the 2" cap barrels, that have an inbuilt threaded insert. Please note that no nut is supplied with this tap. TIP: The best "off" position for this tap is not where the lever is pushed fully back. If you look at the tap from above when the lever is pushed fully back it will be at the 2 o'clock position. If you bring the lever forward slightly to the 3 o'clock position this will give you the best seal. Learn More
  6. S30 METAL BARREL VALVE
    S30 METAL BARREL VALVE
    £7.99
    This is a standard S30 valve, i.e. no piercing pin. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  7. BARREL CAP 4" WITH HOLE, KING KEG
    BARREL CAP 4" WITH HOLE, KING KEG
    £4.00
    Please note that no "O" ring is supplied with this cap. If you need one please separately order an "O-RING FOR KING KEG 4" CAP" in this section. Learn More
  8. CLEAR INLET RUBBER FOR S20/30 VALVE
    CLEAR INLET RUBBER FOR S20/30 VALVE
    £0.49
    Spare part for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  9. BARREL 2 GALLON (10 LITRE)
    BARREL 2 GALLON (10 LITRE)
    £25.99
    This small,16 pint, bottom tap beer barrel is useful for experimental or speciality brews. Please note there is no pressure inject valve with this barrel, just a pressure release to vent excess pressure in it's 2" cap. This product should not be placed where damage could occur in the event of any leakage. TIP: The best "off" position for the tap on this barrel is not where the lever is pushed fully back. If you look at the tap from above when the lever is pushed fully back it will be at the 2 o'clock position. If you bring the lever forward slightly to the 3 o'clock position this will give you the best seal. Learn More
  10. BASIC BARREL 5 GALLON (22.5 litre)
    BASIC BARREL 5 GALLON (22.5 litre)
    £26.50
    Please note there is no pressure inject valve with this beer barrel but it does have a pressure release valve in it's 2" cap to vent excess pressure. This product should not be placed where damage could occur in the event of any leakage. TIP: The best "off" position for the tap on this barrel is not where the lever is pushed fully back. If you look at the tap from above when the lever is pushed fully back it will be at the 2 o'clock position. If you bring the lever forward slightly to the 3 o'clock position this will give you the best seal. Learn More
  11. BARREL CAP SPANNER FOR 4" CAPS
    BARREL CAP SPANNER FOR 4" CAPS
    £8.80
    Out of stock
    Suitable for undoing King Keg and Brewmaster barrel caps, however it should never be used for tightening as it is easy to over-tighten. Learn More
  12. O-RING FOR KING KEG 4" CAP
    O-RING FOR KING KEG 4" CAP
    £1.99
    Out of stock
    Not suitable for Brewmaster barrels. Learn More
  13. BARREL CAP 2", VENTED (WHITE WASHER)
    BARREL CAP 2", VENTED (WHITE WASHER)
    £4.69
    Out of stock
    The colour of the cap we supply may be black or white. Learn More
  14. STANDARD BARREL 5 GALLON (22.5 litre) WITH PIN VALVE
    STANDARD BARREL 5 GALLON (22.5 litre) WITH PIN VALVE
    £33.49
    This beer barrel is fitted with an S30 valve in it's 2" cap that includes a pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders). To use 8g CO2 bulbs with this valve you will need to separately purchase an 8g GAS BULB HOLDER. The bulbs are available in most towns. Note that you only need to add gas if you have exhausted the natural pressure inside the barrel. This product should not be placed where damage could occur in the event of any leakage. S30 is a registered Trade Mark of Hambleton Bard Ltd. TIP: The best "off" position for the tap on this barrel is not where the lever is pushed fully back. If you look at the tap from above when the lever is pushed fully back it will be at the 2 o'clock position. If you bring the lever forward slightly to the 3 o'clock position this will give you the best seal. Learn More
  15. BARREL CAP 2", WITH PIN VALVE (WHITE WASHER)
    BARREL CAP 2", WITH PIN VALVE (WHITE WASHER)
    £12.49
    The colour of the cap we supply may be black or white. This cap is fitted with an S30 valve that has a piercing pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders), you will also need to separately purchase an 8g GAS BULB HOLDER unless you already have one. S30 is a registered Trade Mark of Hambleton Bard Ltd. We recommend that you do not use this cap with the 2 gallon barrel as it would be easy to overpressurise that size of barrel. Learn More
  16. PACK OF 10 O-RINGS FOR S20/30 VALVE
    PACK OF 10 O-RINGS FOR S20/30 VALVE
    £4.99
    Out of stock
    Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  17. PACK OF 10 BASE SEALING VALVE RUBBER WASHERS
    PACK OF 10 BASE SEALING VALVE RUBBER WASHERS
    £5.75
    Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  18. PACK OF 10 BROWN PRESSURE RELEASE VALVE RUBBERS
    PACK OF 10 BROWN PRESSURE RELEASE VALVE RUBBERS
    £4.00
    Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  19. S20 / S30 METAL BARREL PIN VALVE
    S20 / S30 METAL BARREL PIN VALVE
    £8.99
    This S30 valve is fitted with a piercing pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders), you will also need to separately purchase an 8g GAS BULB HOLDER unless you already have one. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More
  20. 8gm GAS BULB HOLDER
    8gm GAS BULB HOLDER
    £3.49
    This holder can be used to inject carbon dioxide gas from 8g CO2 bulbs into a barrel fitted with an S30 valve that includes a pin for piercing 8g CO2 bulbs. The bulbs are available in most towns. S30 is a registered Trade Mark of Hambleton Bard Ltd. Learn More