 | BREWMASTER TOP TAP BARREL WITH FLOAT AND PIN VALVE Ref: 1636
Complete with built-in DRIP TRAY this TOP TAP pressure barrel offers greater flexibility in use than a conventional bottom tap barrel. It can be stored on the floor and the beer can still be drawn off! This is achieved by a tube plugged into the back of the tap, on the other end of which is a FLOAT. The pressure inside the barrel delivers the beer and the float ensures that the clearest beer, from near the surface, reaches the glass! The wide neck gives good access for cleaning. Height 50cm, width 38cm. Beer capacity 40 pints. This barrel is fitted with an S30 valve that includes a pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders). To use 8g CO2 bulbs with this valve you will need to separately purchase an 8g GAS BULB HOLDER. The bulbs are available in most towns. Note that you only need to add gas if you have exhausted the natural pressure inside the barrel. This product should not be placed where damage could occur in the event of any leakage. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £49.99 |
|
|
| KING KEG TOP TAP BARREL WITH FLOAT AND PIN VALVE Ref: 753
A TOP TAP pressure barrel offers greater flexibility in use than a conventional bottom tap barrel. It can be stored on the floor and the beer can still be drawn off! This is achieved by a tube plugged into the back of the tap, on the other end of which is a FLOAT. The pressure inside the barrel delivers the beer and the float ensures that the clearest beer, from near the surface, reaches the glass! The wide neck gives good access for cleaning. Height 46cm, width 35cm. Beer capacity 40 pints. This barrel is fitted with an S30 valve that includes a pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders). To use 8g CO2 bulbs with this valve you will need to separately purchase an 8g GAS BULB HOLDER. The bulbs are available in most towns. Note that you only need to add gas if you have exhausted the natural pressure inside the barrel. This product should not be placed where damage could occur in the event of any leakage. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £48.49 |
|
|
| KING KEG BOTTOM TAP BARREL AND PIN VALVE Ref: 752
This is a good sturdy 5 gallon pressure barrel with a large diameter cap so that you can get inside for cleaning. Pressure valve included. Height 46cm, width 35cm. Beer capacity 40 pints. This barrel is fitted with an S30 valve that includes a pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders). To use 8g CO2 bulbs with this valve you will need to separately purchase an 8g GAS BULB HOLDER. The bulbs are available in most towns. Note that you only need to add gas if you have exhausted the natural pressure inside the barrel. This product should not be placed where damage could occur in the event of any leakage. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £47.49 |
|
|
| 8gm GAS BULB HOLDER Ref: 1710
This holder can be used to inject carbon dioxide gas from 8g CO2 bulbs into a barrel fitted with an S30 valve that includes a pin for piercing 8g CO2 bulbs. The bulbs are available in most towns. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £3.49 |
|
|
| INJECTOR VALVE FOR 8g CO2 BULBS Ref: 790
This device can be used to inject carbon dioxide gas into a barrel that is fitted with a standard S20 / S30 METAL BARREL VALVE that has no pin for piercing 8g CO2 bulbs. The bulbs are available in most towns. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £9.25 |
|
|
| BASIC BARREL 5 GALLON Ref: 765
Please note there is no pressure inject valve with this barrel, just a pressure release to vent excess pressure. Unlike the wide neck barrels above the small diameter cap limits access for cleaning. This product should not be placed where damage could occur in the event of any leakage.
Price: £25.69 |
|
|
 | WHITE 2g BARREL (MASTER 10 LITRE) Ref: 767
This small ,16 pint, barrel is useful for experimental or speciality brews. This product should not be placed where damage could occur in the event of any leakage.
Price: £25.99 |
|
|
| BARREL CAP 4"+S30 BRASS PIN VALVE, KING KEG Ref: 1806
This cap is fitted with an S30 valve that includes a pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders). To use 8g CO2 bulbs with this valve you will need to separately purchase an 8g GAS BULB HOLDER. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £13.49 |
|
|
| BARREL CAP 4"+S30 BRASS VALVE, KING KEG Ref: 1258
This cap is fitted with a standard S30 valve, i.e. no pin. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £12.99 |
|
|
| BARREL CAP 4" WITH HOLE, KING KEG Ref: 780
Please note that no "O" ring is supplied with this cap. If you need one please separately order an "O-RING FOR KING KEG 4" CAP" in this section.
Price: £7.99 |
|
|
| BLACK O-RING FOR KING KEG 4" CAP Ref: 760
Not suitable for Brewmaster barrels.
Price: £1.99 |
|
|
| S20 / S30 METAL BARREL PIN VALVE (BRASS) Ref: 1774
This S30 valve is fitted with a piercing pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders), you will also need to separately purchase an 8g GAS BULB HOLDER unless you already have one. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £8.99 |
|
|
| S20 / S30 METAL BARREL VALVE (BRASS) Ref: 791
This is a standard S30 valve, i.e. no piercing pin. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £7.99 |
|
|
| 2" BARREL CAP WITH PIN VALVE (WHITE WASHER) Ref: 1907
This cap is fitted with an S30 valve that has a piercing pin for use with 8g CO2 bulbs (the valve cannot be used with screw-on gas cylinders), you will also need to separately purchase an 8g GAS BULB HOLDER unless you already have one. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £12.49 |
|
|
| FLAT WHITE WASHER FOR 2" CAPS Ref: 748
Price: £1.30 |
|
|
| 2" BARREL CAP VENTED (WHITE WASHER) Ref: 750
Price: £4.69 |
|
|
| BARREL FLOAT Ref: 758
This is the float that is fitted to King Keg barrels.
Price: £6.39 |
|
|
| BARREL CAP SPANNER FOR 4" CAPS Ref: 763
Suitable for undoing King Keg and Brewmaster barrel caps, however it should never be used for tightening as it is easy to over-tighten.
Price: £8.79 |
|
|
| DRUM TAP + NUT, LONG PARALLEL THREAD Ref: 908
This is the tap that is fitted to the King Keg barrels.
Price: £5.99 |
|
|
| QUICKSERVE TAP (LEVER ACTION) Ref: 907
This tap has a tapered thread and should only be used with barrels that have an inbuilt threaded insert. Please note that no nut is supplied with this tap.
Price: £5.99 |
|
|
| PACK OF 10 BASE SEALING VALVE RUBBER WASHERS Ref: 1819
Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £5.75 |
|
|
| PACK OF 10 BROWN PRESSURE RELEASE VALVE RUBBERS Ref: 1818
Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £3.99 |
|
|
| CLEAR INLET RUBBER FOR S20/30 VALVE Ref: 775
Spare part for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £0.49 |
|
|
| PACK OF 10 O-RINGS FOR S20/30 VALVE Ref: 1820
Spare parts for S30 valves. S30 is a registered Trade Mark of Hambleton Bard Ltd.
Price: £4.99 |
|
|
| YELLOW PRESSURE RELEASE RUBBER FOR BEERSPHERE Ref: 771
Spare part for Beersphere valves.
Price: £0.89 |
|
Secure SSL Credit Card Payment system 
